天天IC网> 企业新闻

NCV8718BMT330TBG

时间:2022-09-08 16:27发布企业:深圳市楷瑞达电子科技有限公司
联系人:张静雯电话:13798528975Q Q:

NCV8718BMT330TBG一级优质供应原装正品现货

该 NCV8718是300毫安 lDO 线性稳压器。它是一种稳定、准确的超低静态电流消耗装置。4 A 超过全温度范围)和一个宽输入电压范围(高达24伏)。该调节器采用了几个保护功能,如热关机和电流限制。

操作输入电压范围: 2.5 V 至24 V •固定电压选项可用: 1.2 V 至5 V (根据要求)•可调电压选项从1.2 V 至5 V •超低静态电流: 类型。4 A 超过温度• ± 2% 超过满载、线路和温度变化• PSRR: 60 dB at 1 kHz •噪音: 类型。36 vRMS 从100Hz 到100kHz •稳定的小1 f 陶瓷电容•软启动以减少涌流和过冲•热关闭和电流限制保护•高速脉冲/高输出/静态/动态 SOA 限制•可选择主动放电(根据要求)• WDFN62x2毫米封装•汽车和其他应用需要独特的站点和控制更改要求的 NCV 前缀; AEC-Q100合格和 PPAP 能力; 设备温度等级1:-40 ° C 至 + 125 ° C 环境工作温度范围•这些设备无铅、无卤素/无 BFR,并且符合 RoHSCompliant

无线充电器•便携式设备•通信系统•车载网络•远程通信、信息娱乐和集群•通用汽车

除非另有说明,产品参数性能在列出的测试条件的电气特性中指明。如果在不同条件下操作,产品性能不能用电气特性来表示。经设计及/或角色塑造生产测试,在温度为摄氏25度时,其性能能保证在指定的操作温度范围内。低占空比脉冲技术在测试过程中使用,以保持结温尽可能接近环境。低于2.1 V 的电压变量的电压压降由最小输入电压2.5 V 给出5。尊重 SOA6。由设计和角色塑造保证。

The NCV8718 is the member of new family of Wide Input Voltage Range Low Dropout Regulators which delivers Ultra Low Ground Current consumption, Good Noise and Power Supply Rejection Ratio Performance. The NCV8718 incorporates EN pin and soft−start feature for simple controlling by microprocessor or logic. Input Decoupling (CIN) It is recommended to connect at least 1 F ceramic X5R or X7R capacitor between IN and GND pin of the device. This capacitor will provide a low impedance path for any unwanted AC signals or noise superimposed onto constant input voltage. The good input capacitor will limit the influence of input trace inductances and source resistance during sudden load current changes. Higher capacitance and lower ESR capacitors will improve the overall line transient response. Output Decoupling (COUT) The NCV8718 does not require a minimum Equivalent Series Resistance (ESR) for the output capacitor. The device is designed to be stable with standard ceramics capacitors with values of 1 F or greater. The X5R and X7R types have the lowest capacitance variations over temperature thus they are recommended. Power Dissipation and Heat Sinking The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material, and the ambient temperature affect the rate of junction temperature rise for the part. For reliable operation junction temperature should be limited to +125°C. The maximum power dissipation the NCV8718 can handle is given by: PD(MAX) TJ(MAX)  TA RJA (eq. 1) The power dissipated by the NCV8718 for given application conditions can be calculated from the following equations: PD  VINI GND(IOUT) I OUTVIN  VOUT (eq. 2) or VIN(MAX)  PD(MAX) VOUT I OUT I OUT I GND (eq. 3) Hints VIN and GND printed circuit board traces should be as wide as possible. When the impedance of these traces is high, there is a chance to pick up noise or cause the regulator to malfunction. Place external components, especially the output capacitor, as close as possible to the NCV8718, and make traces as short as possible.

上一篇:TPS3899PL16DSERQ1
下一篇:MAX20004AFOD/VY+